News

PurgExtra® Tube and Pipe Purging System

08W-PurgExtra-PipeWeldPurgeSystemWeld purging is essential when welding metal tubes and pipes made from titanium, ultra high purity stainless steel joints and just as important when welding those less critical stainless steel and copper nickel pipe joints, in order to achieve non-oxidised, zero colour welds.

PurgExtra® is the latest weld purging product released by Huntingdon Fusion Techniques HFT® for the purging of tube and pipe joints from 1 – 24” ø. This range complements the PurgElite® series, but has extra purge gas inlets and corresponding exhaust ports.

Luke Keane, Distributor Support for HFT® said: “The PurgExtra® System allows the operator to purge at recommended rates initially and then when it would be an advantage, to introduce additional purge gas to create the desired results. Typical applications are for extra inert gas with titanium welds to achieve the lower oxygen levels required for welding that material, which would be around 20 parts per million.

When welding joints where interpass temperature control is necessary, PurgExtra® allows extra argon gas into the welding zone, which will help cooling dramatically. Also for the removal of additional gases that are expelled by the outgassing that occurs as the metal is being heated. The extra gas flow will prevent these expelled gases from combining with the hot metal and oxidising them, which causes the metal to discolour and lose its corrosion resistance.

PurgExtra® comprises of two inflatable dams connected by a heat resistant, highly flexible gas hose that has the unique IntaCal® gas release system. IntaCal® allows the dams to be inflated correctly and then releases the inert gas to safely purge the space between the dams and replaces the old fashioned, complicated valves, still used by other types of purging devices, that might sometimes fail causing the dams to burst.

The highly flexible spinal hose between the dams allows the PurgExtra® Systems to be pulled or pushed easily around bends and elbows. In the centre of the spinal hose a strip of RootGlo® material is adhered, allowing the welder to see clearly when the PurgExtra® System has reached the correct position in the pipe. RootGlo® can be charged by exposing it to daylight for 10 minutes, after which it will provide up to 24 hours of bright illumination inside the pipe.

The innovative PurgeGate® Valve may be fitted to the PurgExtra® Systems as an accessory, to protect the inflatable dams from bursting due to accidental or faulty opening of gas supply valves significantly above the recommended flow rate.

Heat Resistant Covers are also available for PurgExtra®, which fit onto the inflatable dams and allow operation with post-weld heat-treated pipe joints where the temperatures might reach 760°C.

Huntingdon Fusion Techniques HFT® have a Worldwide Exclusive Distributor network.
Please visit www.huntingdonfusion.com.

More Product Details


For more information, please contact:

 

Press:      This email address is being protected from spambots. You need JavaScript enabled to view it.
Sales: This email address is being protected from spambots. You need JavaScript enabled to view it.
Tel.: +44 1554 836 836

 



This Press Release is Succesfully Published in Worldwide Magazines, by clicking the logo you can read the article:

 

Logo Energy Global NEW

Logo The Fabricator

Logo Archy UK

 

 

Logo GasWorld

Logo-oilecho

 

Logo OilVoice

Logo Wire and Tube News Logo TubeFirst NEW 
Logo ITA Logo Thomasnet 
Logo The Fabricator Logo-rabian Oil and Gas 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 


Huntingdon Fusion Techniques HFT® are proud members of:

Logo AWS 2 Logo TWI Logo ITA

You are not allowed to use or copy any of this material or content without the written permission of Huntingdon Fusion Techniques HFT®, copyright protected. All rights belong to Huntingdon Fusion Techniques HFT® exclusively. Not for any reproduction without consent.